English
Polski
Česky
Deutsch
Irish
Magyar
Português
Română
Slovenský
A set of active converters for Ethernet and PoE transmission over coaxial cable, 1 channel 100 Mbps, PoE IN 802.3at/af or Passive (xCOAX3-SW), PoE OUT Passive up to 500 m.
• Transmission range over coaxial cable up to 500 m at 100 Mbps
• Noise immunity and watchdog function in COAX path
• Power supply from switch PoE 802.3at/af or PoE PASSIVE
• Power supply to receiver PoE 802. 3at/af or PoE PASSIVE receivers
up to 30 W total power in the whole power path
• Very low power consumption – 1,35 W for the entire path
• Compact modules
• Clear, optical indication of power and data transmission status
• Easy and quick startup without configuration of parameters
• Noise immunity and watchdog function in COAX path
• Power supply from switch PoE 802.3at/af or PoE PASSIVE
• Power supply to receiver PoE 802. 3at/af or PoE PASSIVE receivers
up to 30 W total power in the whole power path
• Very low power consumption – 1,35 W for the entire path
• Compact modules
• Clear, optical indication of power and data transmission status
• Easy and quick startup without configuration of parameters
ETH10-2wire-SET is a set of active converters designed for Ethernet data and PoE power transmission using only 2 wires.
• A set of converters for Ethernet data and PoE power transmission using 2 wires (e.g. one pair of UTP cable)
• Enables installation of cameras or other IP PoE devices in places where it is difficult or uneconomic to replace the existing wiring
• Power from any PoE switch or 10. ..56 V
• Maximum transmission range is 1000 m, depending on the type, length and cross-section of the cables
• Small size allows easy installation in small spaces, such as in an installation box.
• Enables installation of cameras or other IP PoE devices in places where it is difficult or uneconomic to replace the existing wiring
• Power from any PoE switch or 10. ..56 V
• Maximum transmission range is 1000 m, depending on the type, length and cross-section of the cables
• Small size allows easy installation in small spaces, such as in an installation box.
The device reduces the voltage at a DC plug to 12 V and simultaneously transfers the PoE power supply to the RJ45 output.
• PoE voltage reduction from 48V to 12V – available at a DC plug (illuminator, microphone, heater)
• Provides PoE power supply from the input to the RJ45 output (camera power supply)
• Can be powered with PoE 802.3af or PASSIVE switch
• Compact module size
• Provides PoE power supply from the input to the RJ45 output (camera power supply)
• Can be powered with PoE 802.3af or PASSIVE switch
• Compact module size
The xPoE-4-11A-HS has been designed as LAN extender (repeater) and PoE power supply.
• Compact device size
• Powered from another PoE switch in 802.3at, 802.3af or Passive (PoE IN port)
• Possibility to power up to 3 PoE receivers 802. 3 PoE 802. 3at/af or PASSIVE receivers (PoE OUT ports)
• Power can be turned off on selected PoE ports
• Improves and distributes network signal (fully functional 100Mbps switch)
• Up to 40W total power for all ports
• Electronic fuse on PoE IN input Electronic fuse on PoE IN input
• Cascade power supply (one xPoE powers another)
• Easy and fast startup without configuring parameters
• Selectable PoE standard (at/af)
• Sequential start of PoE outputs
• Very low power consumption (<0.5W)
• Powered from another PoE switch in 802.3at, 802.3af or Passive (PoE IN port)
• Possibility to power up to 3 PoE receivers 802. 3 PoE 802. 3at/af or PASSIVE receivers (PoE OUT ports)
• Power can be turned off on selected PoE ports
• Improves and distributes network signal (fully functional 100Mbps switch)
• Up to 40W total power for all ports
• Electronic fuse on PoE IN input Electronic fuse on PoE IN input
• Cascade power supply (one xPoE powers another)
• Easy and fast startup without configuring parameters
• Selectable PoE standard (at/af)
• Sequential start of PoE outputs
• Very low power consumption (<0.5W)
3-port PoE switch 10/100Mbps, extender (1xPoE IN 802.3at/af + 2xPoE OUT), PoE (max 40W), sequential start PoE OUT
• Miniature design for mounting in camera base
• Powered from another PoE switch supporting 802.3at, 802.3af or Passive standard (PoE IN port)
• Power up to 2 PoE receivers 802. 3at/af or Passive (PoE OUT ports)
• Cascade power supply (one switch powers another)
• Strengthens and distributes network signal (fully functional 100Mbps switch)
up to 40W total power
• Easy and fast startup without configuration of parameters
• Wide operating temperature range
• Very low power consumption (< 0.5 W)
• Sequential start of PoE outputs
• Powered from another PoE switch supporting 802.3at, 802.3af or Passive standard (PoE IN port)
• Power up to 2 PoE receivers 802. 3at/af or Passive (PoE OUT ports)
• Cascade power supply (one switch powers another)
• Strengthens and distributes network signal (fully functional 100Mbps switch)
up to 40W total power
• Easy and fast startup without configuration of parameters
• Wide operating temperature range
• Very low power consumption (< 0.5 W)
• Sequential start of PoE outputs
Switch for 5 IP cameras, in outdoor housing, 6-port 10/100Mbps (5xPoE + 1xUplink), PoE power supply on 4 pairs, integrated power supply 55V 90 W.
• Compact size
• Powering 5 PoE 802. 3at/af or PASSIVE receivers
• Power can be switched off on selected PoE ports
• Clear optical indication of power and data transmission status
• Up to 40 W power per single PoE port (total 90W power budget)
• Easy and fast startup without having to configure parameters
• High efficiency of integrated power supply (>90%)
• Additional screw connector makes it easy to pick up 55 VDC power to other devices
• Scalability by attaching additional switches of xPoE/IP series and IPB/IPUPS
• Supply of cables can be hidden inside the enclosure
• Cable exit through 2x29 mm rubber glands installed in the enclosure
• Cables with crimped plugs (after cutting the plugs) can be inserted
• Power cable and 2 brackets included for enclosure installation without compromising the IP55 protection degree
• Powering 5 PoE 802. 3at/af or PASSIVE receivers
• Power can be switched off on selected PoE ports
• Clear optical indication of power and data transmission status
• Up to 40 W power per single PoE port (total 90W power budget)
• Easy and fast startup without having to configure parameters
• High efficiency of integrated power supply (>90%)
• Additional screw connector makes it easy to pick up 55 VDC power to other devices
• Scalability by attaching additional switches of xPoE/IP series and IPB/IPUPS
• Supply of cables can be hidden inside the enclosure
• Cable exit through 2x29 mm rubber glands installed in the enclosure
• Cables with crimped plugs (after cutting the plugs) can be inserted
• Power cable and 2 brackets included for enclosure installation without compromising the IP55 protection degree
