English
Polski
Česky
Deutsch
Irish
Magyar
Português
Română
Slovenský
Power adapter with 5 VDC voltage and 2 A current output, equipped with USB type A connector.
• Output voltage 5 VDC
• Output current 2A
• USB type A port
• Color: black
• Output current 2A
• USB type A port
• Color: black
This multiplexer is used for splitting signal among multiple TV receivers. It is advised to use the device if a passive splitter lowers the signal to an unacceptable level. The device has four outputs. A power supply is not included. The splitter is to be powered through the No. 4 output ...
5-862 MHz band, 17 dB rejection loss. 4dB through loss, 75 Ohm in/out impedance. Allows to connect multiple receivers to a single antenna. Can also be used as an antenna adder. Built on an un-coupling transformer. Input, output - F-type plugs. Can be installed on a mast. Direct current flow possibil...
BNC connector designed for H155 coaxial cable with an impedance of 50 ohms.
• For H155 cable
• Impedance 50 ohms
• Impedance 50 ohms
The RV-1/2P-UHD multiplexer is designed to split signals from two sources without any loss of quality of the signal.
• Signal splitting from 1 to 2 outputs
• Input splitting configuration with jumpers
• Input splitting configuration with jumpers
D-SEP/HD is a 1-channel galvanic separator for signals transmitted via 75 ohm coaxial cable.
• Isolation between different points of the system, such as cameras and DVR
• Potential difference protection
• Signals in CVBS, AHD, HD-CVI and HD-TVI up to 8 MP.
• Potential difference protection
• Signals in CVBS, AHD, HD-CVI and HD-TVI up to 8 MP.
LZ-1 is a passive device distributing power from a single power supply source.
LZ-8/POL is a simple DC power supply distributor that provides power from one higher power unit to a number of devices. The distributor splits the input into 8 outputs; each of them is protected by polymer fuse...
Switched-mode power supply designed to power 12 VDC electrical devices equipped with 2.1/5.5 socket, with current consumption not exceeding 1A. It is suitable for the majority of CCTV cameras.
• Power supply dedicated for CCTV cameras
• 12 VDC output
• Max load: 1 A
• Over-current protection
• Over-voltage protection
• Short-circuit protection
• 12 VDC output
• Max load: 1 A
• Over-current protection
• Over-voltage protection
• Short-circuit protection
The M18171 AC/DC adapter dedicated for 12 VDC CCTV cameras operates in switching mode and can be placed outdoors on a wall (due to IP53 rating, the splash-proof housing should be protected by a roof/canopy). The connectors of the camera can be placed inside the housing of the power supply.
Switched-mode power supply designed to power 5 VDC electronic devices equipped with 2.1/5.5 socket ("+" in the midpoint), with current consumption not exceeding 2 A.
Switched-mode power supply designed to power 12 VDC electrical devices equipped with 2.1/5.5 socket, with total current consumption not exceeding 2A.
• AC/DC adapter dedicated for CCTV cameras
• Output voltage: 12 VDC
• Max output current: 2 A
• Over-current protection
• Over-voltage protection
• Short-circuit protection
• Output voltage: 12 VDC
• Max output current: 2 A
• Over-current protection
• Over-voltage protection
• Short-circuit protection
Switched-mode power supply designed to power 12 VDC electrical devices equipped with 2.1/5.5 socket, with current total consumption not exceeding 5A. It is suitable for the majority of CCTV cameras.
• AC/DC adapter dedicated for CCTV systems
• 12 VDC output
• Current capacity: 5 A
• Over-current protection
• Over-voltage protection
• Short-circuit protection
• 12 VDC output
• Current capacity: 5 A
• Over-current protection
• Over-voltage protection
• Short-circuit protection
The VHD-15 amplifier/repeater is designed to amplify high resolution AHD, HD-CVI or HD-TVI video signal transmitted over a long distance via a twisted-pair (UTP) or coaxial cable.
A single device compensates the attenuation of about 150 m UTP cable or 300-500 m coaxial cable (depending on the type ...
• Standard:AHD - 4 Mpx, HD-CVI - 1080p, HD-TVI - 5 Mpx, CVBS - PAL / NTSC
• Signal compensation: 150 m twisted-pair cable, 300 m RG-59, 500 m Triset-113
• Signal compensation: 150 m twisted-pair cable, 300 m RG-59, 500 m Triset-113
ZR12-100/LZ-8P is a power supply unit designed for mounting in 19" RACK cabinets. The unit provides 12 VDC output voltage available at 8 screw outputs, each with 1 A current capacity. Each output is protected with a polymer fuse and monitored with a green LED (during operation, a dark LED means blow...
ZR12-150/LZ-12 is a power supply unit designed for mounting in 19" RACK cabinets. The unit provides 12 VDC output voltage available at 12 screw outputs, each with 1 A current capacity. Each output is protected with a polymer fuse and monitored with a green LED (during operation, a dark LED means blo...
ZR12-150/LZ-16/POL is a power supply unit designed for mounting in 19" RACK cabinets. The unit provides 12 VDC output voltage available at 16 screw outputs, each with 0.75 A current capacity. Each output is protected with a polymer fuse and monitored with a green LED (during operation, a dark LED me...
The POE-802.3AF/C M1896 DC-DC converter provides power supply to 12 VDC devices (typically IP CCTV cameras without PoE option), converted from any PoE source (802.3af or 802.3at) distributing 44-57 VDC voltage.
The MP-6 / D microphone is designed for creating sound channel in various applications. The device has two outputs - the balanced (differential) output allows to transmit sound over longer distances via twisted pair cable, whereas unbalanced audio output can be used with coaxial cable, over shorter ...
The OR-150/T M5181 powder-painted steel clamp allows for mounting a camera on a pole/post with a diameter from 70 to 280 mm. The clamp is fixed to the pole with steel strips (1 meter long) and is suitable for cameras with four mounting holes (large adjustment range).
The L5556 holder has been specially designed for ULTIMODE FAST-MS1 L5550 mechanical splices. It can hold up to six such splices. The compact size and mounting hole for a screw allow for easy application of the product in optical boxes, distribution frames etc.
The Delta DRC-24V60W-1AZ 60 W switched-mode power supply is designed to supply power to electronic equipment that requires 24 VDC supply.
• Power output: 60 W
• Output voltage: DC 24 V
• Output voltage adjustment range: DC 24 - 28 V
• Output current: 2,5 A
• Protection: overload, overvoltage, short circuit
• Output voltage: DC 24 V
• Output voltage adjustment range: DC 24 - 28 V
• Output current: 2,5 A
• Protection: overload, overvoltage, short circuit
![6-core Signal Cable: YTDY 6X0.5 [100m]](https://www.dipolnet.ro/img/thumbnails/j8606_100+.jpg/9a6cacaffab9c3683ca16ca742165cfa.jpg)
YTDY cable consisting of 6 wires with copper cores of 0.5 mm diameter. Designed for use in alarm and intercom systems.
![8-core Signal Cable: YTDY 8X0.5 [100m]](https://www.dipolnet.com/img/thumbnails/j8608_100+.jpg/a1a549a32c39518c8b1225350b46bfec.jpg)
YTDY cable consisting of 8 wires with copper cores of 0.5 mm diameter.
![10-core Signal Cable: YTDY 10X0.5 [100m]](https://www.ostelsat.hu/img/thumbnails/j8610_100+.jpg/18d561ef8f27b6f6eabbb2cfcc1752a1.jpg)
YTDY cable consisting of 10 wires with copper cores of 0.5 mm diameter. Designed for use in alarm and intercom systems.
The package includes two steel tapes, each 5 m long. They are wrapped around a chimney to hold an antenna mast firmly in place. If the tape is too short, additional 10 m reels can be ordered - E8520. The weight of the clamp: 2.75 kg.
• For mounting masts to chimneys
• Easy installation
• Two steel tapes (5 m long) included
• Optional 10 m reels available
• Weight: 2.75 kg
• Easy installation
• Two steel tapes (5 m long) included
• Optional 10 m reels available
• Weight: 2.75 kg
The package includes two steel tapes, each 5 m long. They are wrapped around a chimney to hold the antenna mast firmly in place. If the tape was to too short, additional 10 m reels can be ordered - E8520. Weight of the clamp: 3.76 kg.
• Antenna chimney mount,
• Mast-chimney distance: 170 mm,
• For masts with diameters 38-50 mm,
• Fixing with two steel tapes (2x 5 m),
• Weight: 3.76 kg.
• Mast-chimney distance: 170 mm,
• For masts with diameters 38-50 mm,
• Fixing with two steel tapes (2x 5 m),
• Weight: 3.76 kg.
The tape has its application in antenna installations. It is used together with chimney clamp OK-43 E8514 and OK-50 E8516 when the tape included is too short. Weight - 1.01 kg.
• Wall mast mount
• Width: 200 mm
• Mounting with 4 screw anchors
• For masts with diameter 38-50 mm
• Weight: 0.87 kg
• Width: 200 mm
• Mounting with 4 screw anchors
• For masts with diameter 38-50 mm
• Weight: 0.87 kg
The OMM-50L13 bracket is designed for mounting antenna masts to walls.
• Mast bracket with wall mounting
• Width 288 mm
• Mounting by four expansion bolts
• For masts with diameter of 38/50 mm
• Mast distance from wall 130 mm
• Width 288 mm
• Mounting by four expansion bolts
• For masts with diameter of 38/50 mm
• Mast distance from wall 130 mm
• Wall mount for antenna masts
• Width: 315 mm
• Each of two pieces mounted with 4 screw anchors
• For masts with diameter 38-50 mm
• Weight: 1.4 kg
• Width: 315 mm
• Each of two pieces mounted with 4 screw anchors
• For masts with diameter 38-50 mm
• Weight: 1.4 kg
The E8535 wall mount is designed to mount an antenna mast to a wall. The kit includes two brackets with support.
• Wall mast mount
• Adjustable distance between mast and wall: 430...700 mm
• Max span (width): 1010 mm
• For masts with diameter 38-50 mm
• Made of galvanized steel
• Mounting with 10 screw anchors
• Weight: 7.85 kg
• Adjustable distance between mast and wall: 430...700 mm
• Max span (width): 1010 mm
• For masts with diameter 38-50 mm
• Made of galvanized steel
• Mounting with 10 screw anchors
• Weight: 7.85 kg
The bracket is made of flat bar 4 mm thick and welded steel pipe, covered with white powder lacquer. Plastic cap prevents water from getting inside. Suitable for mounting antenna mast to a wall. Total weight: 2 kg.
• Wall mast mount
• For masts with diameter 38-50 mm
• Support guarantying stability
• Width: 360 mm
• Distance between mast and wall: ca. 210 mm
• Weight: 2 kg
• For masts with diameter 38-50 mm
• Support guarantying stability
• Width: 360 mm
• Distance between mast and wall: ca. 210 mm
• Weight: 2 kg
• Wall mast mount
• Support guarantying stability
• Width: 550 mm
• For masts with diameter 38-50 mm
• Distance between mast and wall: ca. 365 mm
• Support guarantying stability
• Width: 550 mm
• For masts with diameter 38-50 mm
• Distance between mast and wall: ca. 365 mm
The OR-30-50R90-150 E8558 bracket is used for the parallel installation of two tubular masts. The distance between the masts can be adjusted by setting the length of the arm in the range of 300-500 mm.
The double-mast clamp is used for installing two masts in parallel.
AMSTRAD UMA50U50 mount designed for wall mounting of satellite dishes.
• Bracket designed for satellite dishes up to 150 cm
• Bracket tube diameter: 50 mm
• Mounting: 4 x expansion bolts Ø 10 mm
• Joints enabling mounting to a wall or flat roof
• All electro-galvanized
• Bracket tube diameter: 50 mm
• Mounting: 4 x expansion bolts Ø 10 mm
• Joints enabling mounting to a wall or flat roof
• All electro-galvanized
The UMA-50R100 103 cm adjustable bracket is designed for mounting television antennas and data transmission antennas.
• Can be installed on flat or sloping rooftops
• Universal, easy to install
• Ideal for mounting DVB-T, WiFi/WLAN antennas
• Universal, easy to install
• Ideal for mounting DVB-T, WiFi/WLAN antennas
The MB-3/PLUS E8744 ballast mast base can hold terrestrial TV and communications/Wi-Fi antennas.
Antenna holder [TYPE U] TV-SAT UMU-40U32 designed for mounting TV, telecommunications and SAT antennas. The zinc coating has anti-corrosion properties.
• Medium-sized holder for TV, telecommunications and SAT antennas
• Mounting to a wall or chimney
• Simple yet durable construction
• Galvanized
• Mounting to a wall or chimney
• Simple yet durable construction
• Galvanized
The single 1.5 m long MK series lattice tower segment is made of aluminum. The triangular lattice structure is characterized by extremely high strength.
• Tower height: 1.5 m
• Material: Aluminum
• No need for guys up to a height of 6 m
• Wall thickness: 1.5 mm
• Weight: 5.05 kg
• Material: Aluminum
• No need for guys up to a height of 6 m
• Wall thickness: 1.5 mm
• Weight: 5.05 kg
Base for free-standing lattice tower of MK series. The design of the base allows the tower to be tilted horizontally.
• Base for MK series tower base
• Material: galvanized steel, aluminum
• Design allows the tower to tilt to horizontally
• Weight: 3.01 kg
• Material: galvanized steel, aluminum
• Design allows the tower to tilt to horizontally
• Weight: 3.01 kg
Anchor bolts for concrete foundation with bolt diameter 12 mm, for erecting masts/towers composed of tower sections E9160.
The JK-50 E9163 zinc-plated clamp is used for mounting lightning rods to antenna masts/towers.
• Material: metal
• Fully galvanized
• Mast diameter max. 50 mm
• Weight: 0.24 kg
• Fully galvanized
• Mast diameter max. 50 mm
• Weight: 0.24 kg
Cable gland with 3/4" thread in gray color. The gland protects both the cable from the sharp edges of the device housing and the device from unwanted external influences.
• Material: ABS
• 3/4" thread
• Gray color
• Tightness class: IP68
• 3/4" thread
• Gray color
• Tightness class: IP68
