EN
PL
CZ
DE
IE
HU
PT
RO
SK
ES
Signal GSM-305 A6765 repeater amplifies the GSM signal and distributes it inside buildings. The amplification coverage is approx. 300 sqm.
• Operating band 880-915, 925-960 MHz (GSM+EGSM)
• Gain: 60/60 dB
• Max. output power: 10 dBm
• Indoor coverage area up to 300 square meters
• AGC (ALC) - automatic gain/level control
• MGC - manual gain control
• Compliance with ETSI 303 609-4
• Easy installation (Plug and Play)
• Gain: 60/60 dB
• Max. output power: 10 dBm
• Indoor coverage area up to 300 square meters
• AGC (ALC) - automatic gain/level control
• MGC - manual gain control
• Compliance with ETSI 303 609-4
• Easy installation (Plug and Play)
The Signal GSM-505 repeater is used for the amplification of the GSM signal and its introduction indoors. The amplification area is approximately 500 m².
• Amplification and distribution of GSM+EGSM signals in buildings/rooms
• Indoor coverage area up to 500 square meters
• Automatic level control (AGC, ALC)
• MGC - manual gain control (attenuator)
• Compliance with ETSI 303 609-4 - no problems with out-of-band interference
• Easy installation (Plug and Play)
• Indoor coverage area up to 500 square meters
• Automatic level control (AGC, ALC)
• MGC - manual gain control (attenuator)
• Compliance with ETSI 303 609-4 - no problems with out-of-band interference
• Easy installation (Plug and Play)
The Signal GSM-1205 repeater is used to amplify the GSM signal and introduce it indoors. The amplification area is approximately 1,200 m².
• Band 880-915, 925-960 MHz (GSM+EGSM)
• Gain: 70/70 dB
• Maximum output power: 20 dBm
• Interior coverage area up to 1200 m²
• Automatic gain control (AGC, ALC)
• Manual gain control (MGC)
• Complies with ETSI standard 303 609-4
• Certified by the Institute of Communications
• Easy to install (Plug and Play)
• Gain: 70/70 dB
• Maximum output power: 20 dBm
• Interior coverage area up to 1200 m²
• Automatic gain control (AGC, ALC)
• Manual gain control (MGC)
• Complies with ETSI standard 303 609-4
• Certified by the Institute of Communications
• Easy to install (Plug and Play)
The Signal GDW-505 repeater amplifies GSM/3G/LTE signals inside buildings. The indoor coverage area is up to 500 sqm
• Operating band: GSM, LTE, DCS, 3G
• Gain: 60/65 dB
• Max. output power: 15 dBm
• Indoor coverage area up to 500 sqm
• Automatic gain/level control (AGC/ALC)
• Manual gain control (MGC)
• Meets the requirements of ETSI 303 609-4
• Easy installation (Plug and Play)
• Device status display
• Gain: 60/65 dB
• Max. output power: 15 dBm
• Indoor coverage area up to 500 sqm
• Automatic gain/level control (AGC/ALC)
• Manual gain control (MGC)
• Meets the requirements of ETSI 303 609-4
• Easy installation (Plug and Play)
• Device status display
The antenna is used for receiving and transmitting signals in the 800-980 MHz band. It has a gain of 12.8 dBi and is equipped with a 10 m cable terminated with an N connector.
• Bandwidth 800-980 MHz
• Gain 12.8 dBi
• VSWR <1,8
• Impedance 50 Ω
• Directional antenna
• Cable 10 m
• N-connector
• Gain 12.8 dBi
• VSWR <1,8
• Impedance 50 Ω
• Directional antenna
• Cable 10 m
• N-connector
The antenna is used for receiving and transmitting signals in the 800-980 MHz band. It has a gain of 16.5 dBi and is equipped with a 10 m cable terminated with an N connector.
• Band 800-980 MHz
• Gain 16,5 dBi
• Impedance 50 Ω
• Directional antenna
• Cable 10 m
• N connector
• Gain 16,5 dBi
• Impedance 50 Ω
• Directional antenna
• Cable 10 m
• N connector
The two-way GSM splitter is used to distribute the amplified signal to indoor antennas. The splitter operates in the frequencies 800-2500 MHz.
• Number of outputs: 2
• Bandwidth 800-2500 MHz
• 3.5 dB attenuation
• Connectors: N-sockets
• Bandwidth 800-2500 MHz
• 3.5 dB attenuation
• Connectors: N-sockets
The GSM three-way splitter is used to distribute the amplified signal to indoor antennas. The splitter operates in the 800-2500 MHz band.
• Number of outputs: 3
• Bandwidth 800-2500 MHz
• Assumption 5.5 dB
• Connectors: N-sockets
• Bandwidth 800-2500 MHz
• Assumption 5.5 dB
• Connectors: N-sockets
The antenna is used for receiving and transmitting signals in the 800-980 MHz band. It has a gain of 12 dBi.
• Bandwidth 800-980 MHz
• Gain 12.8 dBi
• VSWR <1,8
• Impedance 50 Ω
• Directional antenna
• Gain 12.8 dBi
• VSWR <1,8
• Impedance 50 Ω
• Directional antenna
The antenna is used for receiving and transmitting signals in the 800-980 MHz band. It has a gain of 16.5 dBi.
• Band: 800-980 MHz
• Gain: 16,5 dBi
• Impedance: 50 Ω
• Directional antenna
• Gain: 16,5 dBi
• Impedance: 50 Ω
• Directional antenna
