EN
PL
CZ
DE
IE
HU
PT
RO
SK
This section includes devices and equipment intended for LTE and GSM signal reception improvement. The offer includes, among others: GSM antennas, LTE antennas, coaxial cables, modem connectors and connectors. A separate branch of our offer is dedicated to GSM repeaters, which solve the problem of poor GSM signal coverage in buildings.
LTE antennas are available in selected band and broadband versions, covering the full LTE reception range for successive generations of the LTE standard, including the latest 5G standard.
When selecting an LTE antenna for a particular modem it is necessary to verify the type of connector in the modem and select the appropriate connector for it.
LTE antennas are available in selected band and broadband versions, covering the full LTE reception range for successive generations of the LTE standard, including the latest 5G standard.
When selecting an LTE antenna for a particular modem it is necessary to verify the type of connector in the modem and select the appropriate connector for it.
The Signal GSM-1205 repeater is used to amplify the GSM signal and introduce it indoors. The amplification area is approximately 1,200 m².
• Band 880-915, 925-960 MHz (GSM+EGSM)
• Gain: 70/70 dB
• Maximum output power: 20 dBm
• Interior coverage area up to 1200 m²
• Automatic gain control (AGC, ALC)
• Manual gain control (MGC)
• Complies with ETSI standard 303 609-4
• Certified by the Institute of Communications
• Easy to install (Plug and Play)
• Gain: 70/70 dB
• Maximum output power: 20 dBm
• Interior coverage area up to 1200 m²
• Automatic gain control (AGC, ALC)
• Manual gain control (MGC)
• Complies with ETSI standard 303 609-4
• Certified by the Institute of Communications
• Easy to install (Plug and Play)
Signal GSM-305 A6765 repeater amplifies the GSM signal and distributes it inside buildings. The amplification coverage is approx. 300 sqm.
• Operating band 880-915, 925-960 MHz (GSM+EGSM)
• Gain: 60/60 dB
• Max. output power: 10 dBm
• Indoor coverage area up to 300 square meters
• AGC (ALC) - automatic gain/level control
• MGC - manual gain control
• Compliance with ETSI 303 609-4
• Easy installation (Plug and Play)
• Gain: 60/60 dB
• Max. output power: 10 dBm
• Indoor coverage area up to 300 square meters
• AGC (ALC) - automatic gain/level control
• MGC - manual gain control
• Compliance with ETSI 303 609-4
• Easy installation (Plug and Play)
The Signal GSM-505 repeater is used for the amplification of the GSM signal and its introduction indoors. The amplification area is approximately 500 m².
• Amplification and distribution of GSM+EGSM signals in buildings/rooms
• Indoor coverage area up to 500 square meters
• Automatic level control (AGC, ALC)
• MGC - manual gain control (attenuator)
• Compliance with ETSI 303 609-4 - no problems with out-of-band interference
• Easy installation (Plug and Play)
• Indoor coverage area up to 500 square meters
• Automatic level control (AGC, ALC)
• MGC - manual gain control (attenuator)
• Compliance with ETSI 303 609-4 - no problems with out-of-band interference
• Easy installation (Plug and Play)
The Signal GDW-505 repeater amplifies GSM/3G/LTE signals inside buildings. The indoor coverage area is up to 500 sqm
• Operating band: GSM, LTE, DCS, 3G
• Gain: 60/65 dB
• Max. output power: 15 dBm
• Indoor coverage area up to 500 sqm
• Automatic gain/level control (AGC/ALC)
• Manual gain control (MGC)
• Meets the requirements of ETSI 303 609-4
• Easy installation (Plug and Play)
• Device status display
• Gain: 60/65 dB
• Max. output power: 15 dBm
• Indoor coverage area up to 500 sqm
• Automatic gain/level control (AGC/ALC)
• Manual gain control (MGC)
• Meets the requirements of ETSI 303 609-4
• Easy installation (Plug and Play)
• Device status display
The connector is used to connect an external antenna to a GPRS/UMTS/LTE modem in order to strengthen the signal of the mobile operator.
• N-plug - N-plug
• Connector length 5 m
• Connector length 5 m
The connector is used to connect an external antenna to a GPRS/UMTS/LTE modem in order to strengthen the signal of the mobile operator.
• Connector length 10 m
The GSM taps are used to distribute the previously amplified GSM signal to the indoor antennas. Branch attenuation 8 dB.
• Transit attenuation <1.3 dB
• Branch attenuation 8 dB
• Isolation between outputs >20 dB
• Bandwidth 800-2500 MHz
• VSWR <1,4
• Connectors: N-sockets
• Branch attenuation 8 dB
• Isolation between outputs >20 dB
• Bandwidth 800-2500 MHz
• VSWR <1,4
• Connectors: N-sockets
The GSM taps are used to distribute the previously amplified GSM signal to the indoor antennas. Branch attenuation 5 dB.
• Transit attenuation <2.2 dB
• Branch attenuation 5 dB
• Inter output isolation >20 dB
• Bandwidth 800-2500 MHz
• VSWR <1,4
• Connectors: N-sockets
• Branch attenuation 5 dB
• Inter output isolation >20 dB
• Bandwidth 800-2500 MHz
• VSWR <1,4
• Connectors: N-sockets
The tap distributes amplified GSM/DSC/UMTS/LTE signals to indoor antennas A741001, A741002. Operating band: 800...2500 MHz; connectors: N-f.
• Breakthrough attenuation <1 dB
• Branch attenuation 12 dB
• Isolation between outputs >20 dB
• Bandwidth 800-2500 MHz
• VSWR <1.4
• Connectors: N-sockets
• Branch attenuation 12 dB
• Isolation between outputs >20 dB
• Bandwidth 800-2500 MHz
• VSWR <1.4
• Connectors: N-sockets
The two-way GSM splitter is used to distribute the amplified signal to indoor antennas. The splitter operates in the frequencies 800-2500 MHz.
• Number of outputs: 2
• Bandwidth 800-2500 MHz
• 3.5 dB attenuation
• Connectors: N-sockets
• Bandwidth 800-2500 MHz
• 3.5 dB attenuation
• Connectors: N-sockets
The GSM three-way splitter is used to distribute the amplified signal to indoor antennas. The splitter operates in the 800-2500 MHz band.
• Number of outputs: 3
• Bandwidth 800-2500 MHz
• Assumption 5.5 dB
• Connectors: N-sockets
• Bandwidth 800-2500 MHz
• Assumption 5.5 dB
• Connectors: N-sockets
