EN
PL
CZ
DE
IE
HU
PT
RO
SK
ES
The FS8114 tester is used for measuring cable continuity, measuring cable length and measuring the distance to cable damage.
• Cable types tested: UTP/STP cat. 5, 5e, 6, 7, telephone, coaxial
• Cable length measurement
• Measurement frequency: 130 kHz
• Measurement method: capacitive
• Maximum length: 2000 m
• Minimum length: 1 m
• "Find port" – quick search of the port in a network device
• Searching and testing cables in PoE mode (passive PoE)
• Pair integrity test
• Measuring voltages on individual conductors (POE)
• Transmitter voltage protection: 60 VAC / 48 VDC
• Auto-OFF function
• Battery discharge indicator
• Record of measurement results in the device memory
• Built-in visual fault locator (VFL) for optical cables
• Power: 9 V battery (included)
• Cable length measurement
• Measurement frequency: 130 kHz
• Measurement method: capacitive
• Maximum length: 2000 m
• Minimum length: 1 m
• "Find port" – quick search of the port in a network device
• Searching and testing cables in PoE mode (passive PoE)
• Pair integrity test
• Measuring voltages on individual conductors (POE)
• Transmitter voltage protection: 60 VAC / 48 VDC
• Auto-OFF function
• Battery discharge indicator
• Record of measurement results in the device memory
• Built-in visual fault locator (VFL) for optical cables
• Power: 9 V battery (included)
The FS8117 cable tester allows to test UTP/STP cables: cable quality, attenuation, length, distance to failure, short-circuit, improperly crimped connectors, Ping test, correct connection to the router, PoE voltage test, scan of active IPs in the network. Precision inductive probe – high power pair ...
• Tested cable types: CAT 5, 5e, 6, 7 twisted pair (UTP/STP), telephone, coaxial
• Cable length testing
• Function - "find port" quick port search on network devices
• Cable search and testing in PoE mode (passive PoE)
• Pair integrity test
• PoE wire voltage measurement
• Auto shutdown at idle
• Battery low indicator
• Recording of measurement results in the device memory
• "Find port" function - quick port search in network devices
• PING test
• IP Scan
• Quick identification of the connected network port
• Cable length testing
• Function - "find port" quick port search on network devices
• Cable search and testing in PoE mode (passive PoE)
• Pair integrity test
• PoE wire voltage measurement
• Auto shutdown at idle
• Battery low indicator
• Recording of measurement results in the device memory
• "Find port" function - quick port search in network devices
• PING test
• IP Scan
• Quick identification of the connected network port
Terminators enable detection and testing of 8 wires (ID2-ID9). They work with FORSCHER FS8117 N7051 meter.
• Number of terminators: 8
• Cable types tested: twisted pair cat. 5, 5e, 6, 7 (UTP/STP)
• Identification of specific twisted pair cable
• Cable types tested: twisted pair cat. 5, 5e, 6, 7 (UTP/STP)
• Identification of specific twisted pair cable
The tester is used to measure the continuity of the cabling. The device is equipped with a terminator.
• LAN cable continuity testing
• UTP, FTP and telephone cables
• RJ45 and RJ11 connectors
• UTP, FTP and telephone cables
• RJ45 and RJ11 connectors
NB-IoT / CAT-M /LTE cat.1 / GSM signal meter for installation, measurement and optimisation of IoT networks.
• Measurement and visualisation of signal quality and strength NB-IoT, CAT-M, LTE cat.1, GSM
• Antenna connectors (2xSMA)
• Two SIM card slots
• Antenna connectors (2xSMA)
• Two SIM card slots
