EN
PL
CZ
DE
IE
HU
PT
RO
SK
ES
The active RTA-120 splitter is a high-quality element of the antenna installation, designed to split the signal between two television receivers.
• Splitting signal into 2 receivers without compromising picture and sound quality
• Operating frequency range: 47-862 MHz - stable operation over a wide frequency band
• Gain control
• High output separation to minimise interference between connected devices
• Low signal attenuation - stable reception of terrestrial DVB-T2 and cable TV
• Power supply via coaxial cable from the output side (OUT)
• Possibility to transfer power voltage from output (OUT) to input (IN)
• Robust, compact metal casing - easy installation even in limited space
• Operating frequency range: 47-862 MHz - stable operation over a wide frequency band
• Gain control
• High output separation to minimise interference between connected devices
• Low signal attenuation - stable reception of terrestrial DVB-T2 and cable TV
• Power supply via coaxial cable from the output side (OUT)
• Possibility to transfer power voltage from output (OUT) to input (IN)
• Robust, compact metal casing - easy installation even in limited space
The active RTA-140 splitter is a high-quality element of the antenna installation, designed to divide the signal into four television receivers.
• Splitting signal into 4 receivers without compromising picture and sound quality
• Operating frequency range: 47-862 MHz - stable operation over a wide frequency band
• Gain control
• High output separation to minimise interference between connected devices
• Low signal attenuation - stable reception of terrestrial DVB-T2 and cable TV
• Power supply via coaxial cable from the output side (OUT)
• Possibility to transfer power voltage from output (OUT) to input (IN)
• Robust, compact metal casing - easy installation even in limited space
• Operating frequency range: 47-862 MHz - stable operation over a wide frequency band
• Gain control
• High output separation to minimise interference between connected devices
• Low signal attenuation - stable reception of terrestrial DVB-T2 and cable TV
• Power supply via coaxial cable from the output side (OUT)
• Possibility to transfer power voltage from output (OUT) to input (IN)
• Robust, compact metal casing - easy installation even in limited space
DC015T antenna diplexer that sums signals from three antennas – signals from FM+VHFI/II band (47-108 MHz), VHFIII (174-230 MHz) and UHF band (470-694 MHz).
• The diplexer enables summing of FM+VHFI/II band (47-108 MHz), VHFIII(174-230 MHz) and UHF band (470-694 MHz) signals
• It is mounted on the antenna tower, near the antenna set
• Die-cast housing inside a compact plastic case
• It is mounted on the antenna tower, near the antenna set
• Die-cast housing inside a compact plastic case
The ZWR-210DC crossover (2 inputs) is used as a summing element for FM/VHF and UHF band signals.
• Inputs: FM/VHF, UHF
• Attenuation: 1 dB
• Separately switchable current transitions in VHF and UHF paths (DC 12 V/100 mA)
• Shielded housing
• Mounting on mast in splash-proof housing by means of a clamp
• Attenuation: 1 dB
• Separately switchable current transitions in VHF and UHF paths (DC 12 V/100 mA)
• Shielded housing
• Mounting on mast in splash-proof housing by means of a clamp
The ZA-104Ms diplexer (3 inputs) is used as a combining element for FM, VHF and UHF band signals (max. DC 24 V/0.2 A).
• Inputs: FM, VHF, UHF
• Attenuation: 1 dB
• Current pass-through in UHF path (max. DC 24 V/ 200mA)
• Shielded housing
• Mounting on mast with cable tie
• F type connectors
• Attenuation: 1 dB
• Current pass-through in UHF path (max. DC 24 V/ 200mA)
• Shielded housing
• Mounting on mast with cable tie
• F type connectors
The ZA-204Ms crossover (3 inputs) is used as a combining element for FM, VHF and UHF band signals (auto DC 12 V/0.6 A).
• Inputs: FM, VHF, UHF
• Attenuation: 1 dB
• Auto DC circuit on all inputs (12 V/100 mA)
• Shielded housing
• Mounting on mast with cable tie
• F-type connectors
• Attenuation: 1 dB
• Auto DC circuit on all inputs (12 V/100 mA)
• Shielded housing
• Mounting on mast with cable tie
• F-type connectors
The ZA-106AMs crossover (2 inputs) is used as a summing element for FM and VHF/UHF band signals.
• Inputs: FM, VHF/UHF
• Attenuation: 1 dB
• Current pass-through in VHF/UHF path (max. DC 24 V/250 mA)
• Shielded housing
• Mounting on mast by means of clamp
• F-type connectors
• Attenuation: 1 dB
• Current pass-through in VHF/UHF path (max. DC 24 V/250 mA)
• Shielded housing
• Mounting on mast by means of clamp
• F-type connectors
The ZA-112Ms antenna diplexer (3 inputs) is used as a combining element for VHF, UHF1 (max. 24 VDC/0,2 A), UHF2.
• Inputs: VHF, UHF1, UHF2
• Attenuation: 1 dB
• Current pass in UHF1 path (max. DC 24 V/200 mA)
• Shielded housing
• Mast mounting with cable tie
• F type connectors
• Attenuation: 1 dB
• Current pass in UHF1 path (max. DC 24 V/200 mA)
• Shielded housing
• Mast mounting with cable tie
• F type connectors
The ZA-106Ms diplexer (2 inputs) is used as a combining element for VHF and UHF band signals (max. DC 24 V/0.25 A).
• Inputs: VHF, UHF
• Attenuation: 1 dB
• Current pass-through in UHF path (max. DC 24 V/250 mA)
• Shielded housing
• Mounting on mast by means of a clamp
• F type connectors
• Attenuation: 1 dB
• Current pass-through in UHF path (max. DC 24 V/250 mA)
• Shielded housing
• Mounting on mast by means of a clamp
• F type connectors
The ZA-206Ms crossover (2 inputs) is used as a combining element for VHF (auto. DC 12 V/0.6 A) and UHF (auto. DC 12 V/0.6 A) band signals.
• Inputs: VHF, UHF
• Attenuation: 1 dB
• Auto DC circuit on all inputs (12 V/60 mA)
• Shielded housing
• Mounting on mast with cable tie
• F-type connectors
• Attenuation: 1 dB
• Auto DC circuit on all inputs (12 V/60 mA)
• Shielded housing
• Mounting on mast with cable tie
• F-type connectors
