EN
PL
CZ
DE
IE
HU
PT
RO
SK
ES
DC015T antenna diplexer that sums signals from three antennas – signals from FM+VHFI/II band (47-108 MHz), VHFIII (174-230 MHz) and UHF band (470-694 MHz).
• The diplexer enables summing of FM+VHFI/II band (47-108 MHz), VHFIII(174-230 MHz) and UHF band (470-694 MHz) signals
• It is mounted on the antenna tower, near the antenna set
• Die-cast housing inside a compact plastic case
• It is mounted on the antenna tower, near the antenna set
• Die-cast housing inside a compact plastic case
The ZWR-210DC crossover (2 inputs) is used as a summing element for FM/VHF and UHF band signals.
• Inputs: FM/VHF, UHF
• Attenuation: 1 dB
• Separately switchable current transitions in VHF and UHF paths (DC 12 V/100 mA)
• Shielded housing
• Mounting on mast in splash-proof housing by means of a clamp
• Attenuation: 1 dB
• Separately switchable current transitions in VHF and UHF paths (DC 12 V/100 mA)
• Shielded housing
• Mounting on mast in splash-proof housing by means of a clamp
The ZA-104Ms diplexer (3 inputs) is used as a combining element for FM, VHF and UHF band signals (max. DC 24 V/0.2 A).
• Inputs: FM, VHF, UHF
• Attenuation: 1 dB
• Current pass-through in UHF path (max. DC 24 V/ 200mA)
• Shielded housing
• Mounting on mast with cable tie
• F type connectors
• Attenuation: 1 dB
• Current pass-through in UHF path (max. DC 24 V/ 200mA)
• Shielded housing
• Mounting on mast with cable tie
• F type connectors
The ZA-204Ms crossover (3 inputs) is used as a combining element for FM, VHF and UHF band signals (auto DC 12 V/0.6 A).
• Inputs: FM, VHF, UHF
• Attenuation: 1 dB
• Auto DC circuit on all inputs (12 V/100 mA)
• Shielded housing
• Mounting on mast with cable tie
• F-type connectors
• Attenuation: 1 dB
• Auto DC circuit on all inputs (12 V/100 mA)
• Shielded housing
• Mounting on mast with cable tie
• F-type connectors
The ZA-106AMs crossover (2 inputs) is used as a summing element for FM and VHF/UHF band signals.
• Inputs: FM, VHF/UHF
• Attenuation: 1 dB
• Current pass-through in VHF/UHF path (max. DC 24 V/250 mA)
• Shielded housing
• Mounting on mast by means of clamp
• F-type connectors
• Attenuation: 1 dB
• Current pass-through in VHF/UHF path (max. DC 24 V/250 mA)
• Shielded housing
• Mounting on mast by means of clamp
• F-type connectors
The ZA-112Ms antenna diplexer (3 inputs) is used as a combining element for VHF, UHF1 (max. 24 VDC/0,2 A), UHF2.
• Inputs: VHF, UHF1, UHF2
• Attenuation: 1 dB
• Current pass in UHF1 path (max. DC 24 V/200 mA)
• Shielded housing
• Mast mounting with cable tie
• F type connectors
• Attenuation: 1 dB
• Current pass in UHF1 path (max. DC 24 V/200 mA)
• Shielded housing
• Mast mounting with cable tie
• F type connectors
The ZA-106Ms diplexer (2 inputs) is used as a combining element for VHF and UHF band signals (max. DC 24 V/0.25 A).
• Inputs: VHF, UHF
• Attenuation: 1 dB
• Current pass-through in UHF path (max. DC 24 V/250 mA)
• Shielded housing
• Mounting on mast by means of a clamp
• F type connectors
• Attenuation: 1 dB
• Current pass-through in UHF path (max. DC 24 V/250 mA)
• Shielded housing
• Mounting on mast by means of a clamp
• F type connectors
The ZA-206Ms crossover (2 inputs) is used as a combining element for VHF (auto. DC 12 V/0.6 A) and UHF (auto. DC 12 V/0.6 A) band signals.
• Inputs: VHF, UHF
• Attenuation: 1 dB
• Auto DC circuit on all inputs (12 V/60 mA)
• Shielded housing
• Mounting on mast with cable tie
• F-type connectors
• Attenuation: 1 dB
• Auto DC circuit on all inputs (12 V/60 mA)
• Shielded housing
• Mounting on mast with cable tie
• F-type connectors
The ZA-F10 in-duct diplexer is used as a combining element for FM/VHF (5-230 MHz) and UHF (470-790 MHz) antenna signals.
• Mounted directly in VHF antenna box
• 12 VDC pass-through between the output and UHF antenna connector (max. 100 mA)
• Insertion loss: 1.5 dB
• Attenuates LTE signals
• 12 VDC pass-through between the output and UHF antenna connector (max. 100 mA)
• Insertion loss: 1.5 dB
• Attenuates LTE signals
The ST 1-69 combiner/splitter makes it possible to connect two antennas from even one band to a single TV receiver or can be used as an antenna splitter.
• Number of inputs: 1
• Number of outputs: 2
• Operating band: 5 - 862 MHz
• Mounting on the mast with a clamp
• Number of outputs: 2
• Operating band: 5 - 862 MHz
• Mounting on the mast with a clamp
The DC015L antenna diplexer sums signals from three antennas - signals from the FM+VHFI/II band (47-108 MHz), VHFIII (174-230 MHz) and the UHF band (470-790 MHz).
• Combining signals from three antennas receiving signals in FM+VHFI/II (47-108 MHz), VHFIII (170-230 MHz) and UHF (470-790 MHz) bands
• Mast-mount just by antennas
• Small size cast metal case put into compact size plastic housing
• Mast-mount just by antennas
• Small size cast metal case put into compact size plastic housing
The SWE 40-01 combiner allows the Quad LNB signal to be combined with the terrestrial TV signal and sent to four RTV/SAT outlets.
• Inputs: 4 SAT + 1 RTV
• Outputs: 4 (RTV + SAT)
• Summing of signal from quad converter with terrestrial TV signal
• Summation of signal to 4 RTV/SAT outlets
• High separation between SAT and TV inputs
• Outputs: 4 (RTV + SAT)
• Summing of signal from quad converter with terrestrial TV signal
• Summation of signal to 4 RTV/SAT outlets
• High separation between SAT and TV inputs
The 9645 KIT multiband converter allows the transmission of two independent satellite signals and a terrestrial TV signal via a single coaxial cable.
• SAT and DVB-T/T2 signals in 1 cable
• Ideal for PVR receivers
• Power supply from satellite receiver
• Transmitter can be installed outdoors
• Converter passes DiseqC signal
• Ideal for PVR receivers
• Power supply from satellite receiver
• Transmitter can be installed outdoors
• Converter passes DiseqC signal
The RSI-02Ms R85315 operates as a combiner or splitter of broadcast signals in the frequency range 47-862 MHz.
• Shielded housing
• Rubber covers for F-plugs
• Pole mounting with cable tie
• Current pass between one of the outputs and the input (max. 24 V/250 mA)
• Can operate as a combiner or splitter
• Rubber covers for F-plugs
• Pole mounting with cable tie
• Current pass between one of the outputs and the input (max. 24 V/250 mA)
• Can operate as a combiner or splitter
The DSE SSC4 combiner allows the Quad LNB signal to be combined with the terrestrial TV signal and sent to four RTV/SAT outlets.
• Inputs: 4 SAT + 1 RTV
• Outputs: 4 (RTV + SAT)
• Summing of signal from quad converter with terrestrial TV signal
• Summation of signal to 4 RTV/SAT outlets
• High separation between SAT and TV inputs
• Outputs: 4 (RTV + SAT)
• Summing of signal from quad converter with terrestrial TV signal
• Summation of signal to 4 RTV/SAT outlets
• High separation between SAT and TV inputs
The MM-307 UHF-UHF-VHF/FM mast crossover on F-connectors is used as a combining element for signals from 3 antennas, mounted on an antenna mast.
• The diplexer allows for the summation of the FM+VHF band (47-260 MHz) and the 2xUHF band (470-862 MHz)
• F connectors
• Mounted on the antenna mast, near the antenna set
• Cased inside a compact plastic housing
• F connectors
• Mounted on the antenna mast, near the antenna set
• Cased inside a compact plastic housing
The MM-214 RTV/SAT diplexer with F-connectors is used as an element which sums up signals from terrestrial and satellite TV antennas.
• RTV/SAT signal booster
• Mounted on a mast near the antenna set
• Allows one cable to transmit signal from satellite converter and terrestrial TV antenna
• Mounted on a mast near the antenna set
• Allows one cable to transmit signal from satellite converter and terrestrial TV antenna
