EN
PL
CZ
DE
IE
HU
PT
RO
SK
€66.80
| Price | Disc. | Quantity | Validity |
|---|---|---|---|
| €66.80 | 0 % | from 1 piece |
Available
The extender set extends the range of the LAN (PoE) on the UTP cable up to 800 m. It is applicable when the PoE switch-receiver distance exceeds 100 m.
• Power supply possible from PoE switch in 802.3af, 802.3at standard, or PoE Passive (PoE IN port)
• Power available to PoE receiver up to 800 m (10 Mbps)
• 100 Mbps available up to a maximum of 500 m
• Clear operating status and bandwidth indication
• Easy and quick start-up without configuring parameters
• Small size of the device enabling installation in small spaces, e.g. in a camera base
• Wide operating temperature range
• Power available to PoE receiver up to 800 m (10 Mbps)
• 100 Mbps available up to a maximum of 500 m
• Clear operating status and bandwidth indication
• Easy and quick start-up without configuring parameters
• Small size of the device enabling installation in small spaces, e.g. in a camera base
• Wide operating temperature range
Details
ETH-ETH500-SET is a set of two extenders to extend the range of a PoE-powered LAN. When installed between any PoE switch and a PoE-powered IP camera, it enables the network range to be extended up to 800 metres using standard UTP cable.
The kit should be used when the distance between the switch and the PoE receiver exceeds 100 metres.
The kit should be used when the distance between the switch and the PoE receiver exceeds 100 metres.
The devices allow cameras or other IP PoE devices to be installed in remote locations where the installation of additional cabling is either impossible or uneconomical. It provides an economical alternative to cabling based on fibre optics and a separate power line.
It will prove useful in installations over large areas, as well as in places where the monitoring system is temporary and the cost of preparing the cabling is important.
It will prove useful in installations over large areas, as well as in places where the monitoring system is temporary and the cost of preparing the cabling is important.
The ETH-ETH500 module can be powered from any PoE switch via an RJ45 port. The ETH-ETH500 modules are then connected to each other via UTP cable via the LONG RANGE ports. The maximum cable length in the LONG RANGE path is up to 800 m. This connection provides bi-directional data transmission and PoE power transfer.
A camera or other PoE receiver must be connected to the RJ45 port of the ETH-ETH500 module at the end of the line. Once the receiver is correctly detected by the power switch, the entire path is automatically powered and the network connection is established.
Once power is applied and the cables are properly connected, the devices establish communication at 100 Mbps. In the event of problems with the quality of the connection, transmission can be automatically downgraded to 10 Mbps, which will be signalled by lighting up the corresponding indicator LED.
A camera or other PoE receiver must be connected to the RJ45 port of the ETH-ETH500 module at the end of the line. Once the receiver is correctly detected by the power switch, the entire path is automatically powered and the network connection is established.
Once power is applied and the cables are properly connected, the devices establish communication at 100 Mbps. In the event of problems with the quality of the connection, transmission can be automatically downgraded to 10 Mbps, which will be signalled by lighting up the corresponding indicator LED.
Key features:
- power supply from a PoE switch using 802.3af, 802.3at, or PoE Passive (PoE IN port)
- power available to PoE receiver up to 800 m (10 Mbps)
- 100 Mbps available up to a maximum of 500 m
- clear operating status and bandwidth indication
- easy and quick start-up without configuring parameters
- small size of the device allowing installation in small spaces, e.g. in a camera base
- wide operating temperature range
Summary of available power and capacity depending on the length of the Long Range track:
| Distance | Maximum power | Maximum throughput |
| 250 m | 50 W | 100 Mbps |
| 500 m | 25 W | 100 Mbps |
| 800 m | 15 W | 10 Mbps |
Primary uses:
- Modernisation of existing analogue CCTV installations to Ethernet-based systems.
- Monitoring of construction sites where, on a limited budget, an installation must be made over a wide area. Low cost cabling with security of use in areas often subject to damage.
- Construction of CCTV installations for photovoltaic farms, playing fields, recreational areas, city parks, etc.
In the case of installation in limited space, it is possible to cut and break out the mounting brackets of the cradle, thus reducing the dimensions of the module.
The ETH-ETH500 modules have the possibility to be powered from external power supplies via additional screw connectors. It is not possible to power the PoE receiver in this mode. Power supply to both devices on both sides of the LONG RANGE path is required for correct operation.
Specifications
| Model | ETH-ETH500-SET | ||
| Applications | Switch PoE | ||
| Manufacturer | ATTE | ||
| Interfaces | |||
| Ethernet ports | number of ports | 2 | |
| Ethernet ports | port types | Fast Ethernet | |
| PoE 10/100/1000 MBps | 3 | ||
| Optical port | Slot SFP | No | |
| PoE properties | |||
| PoE | Yes | ||
| PoE standard | 802.3af, 802.3at, Passive | ||
| Extend mode | Yes | ||
| Device properties | |||
| Power supply | PoE | 802.3af, 802.3at | |
| Number of fans | None | ||
| Dimensions | mm | ||
| Mounting | Desktop, Box mounting | ||
| Redundant supply | No | ||
| Certificates | CE/FCC | ||
| Package content | Manual, Switch | ||
| Operating environment | |||
| Temperature | operation | ℃ | -25...+65 |
